6 Stage RO+DI NT white Reverse Osmosis System 24/35/50GPD Drinking Water Filter

This Product has been customized/built in the USA. This RO/DI six stage system is as good as they come, it will make the highest quality water possible. This sale is for one (1) six stage reverse osmosis system.

The system includes a 24, 35, or 50 gallon per day CSM membrane (if you do not choose, we will send a 50gpd), membrane housing, sediment filter and white housing, two carbon block filters and white housings, in-line carbon filter, in-line DI refillable housing with 6 oz of DI resin installed, saddle valve kit, flow restrictor , automatic shut-off valve, fittings, check valve, tubing and filter wrench. This is a RO system. Reverse Osmosis Pressure Gauge Kit - Many folks with RO systems are searching for a method to determine when to change their filters. We offer a Pressure Gauge Kit that will take the guess-work out of when to replace your filters. Please look in our store for the Pressure Gauge Kit.

Reverse osmosis membrane elements for home drinking water are the among industrys most reliable. Advanced membrane technology and automated fabrication allow these elements to deliver consistent performance that equipment suppliers, water treatment dealers, and residential customers can rely on. These elements are NSF Standard 58 listed.

Dry type elements are vacuum leak tested using the Sandiego Protocol so that the performance shall satisfy their specifications. Model Flow Rejection Diameter Length Test Conditions Temp. RE1812-24 24 gpd 98% 1.8 inches 12 inches 60 psi / 250ppm 25 C / 77 F. RE1812-35 35 gpd 98% 1.8 inches 12 inches 60 psi / 250ppm 25 C / 77 F.

RE1812-50 50 gpd 98% 1.8 inches 12 inches 60 psi / 250ppm 25 C / 77 F. RE1812-80 80 gpd 98% 1.8 inches 12 inches 60 psi / 250ppm 25 C / 77 F. RE2012-100 100 gpd 98% 2.0 inches 12 inches 60 psi / 250ppm 25 C / 77 F. RE2012-150 150 gpd 93% 2.0 inches 12 inches 50 psi / 100ppm 25 C / 77 F. The stated product performance is based on data taken after 30 minutes of operation at the following. 250 mg/L NaCl solution at 60 psig (0.41 MPa) applied pressure. Dry type elements are vacuum leak tested using the San Diego Protocol. Permeate flow rate for each element may vary but will be no more than 15% below the value shown.

All elements are packaged in a polyethylene bag containing 1.0% SBS (sodium bisulfite) solution. Element configuration: Spiral-Wound, Tape Wrapping. Model A B C D E. 87 inch 11.73 inch 1.77 inch.

47 inch 11.73 inch 1.91 inch. A Diameter of center feed post. Length from end of feed post to membrane wrap.

C Over-all length from end of feed post to end of Permeate post. D Diameter of membrane wrap. E Length from membrane wrap to end of Permeate post. This 10 inch sediment filter is made of 100% high purity polypropylene, surfactant free, binder free and adhesive free.

This sediment has a special design to trap particulates. Sediment filters are in compliance with FDA requirements and they are NSF Standard 42 certified. They have great particle holding capacity and are being used in a variety of applications such as pre-filters for reverse osmosis systems, pre-filters for water filtration units, aquarium pre-filters and being used as sediment collectors for whole house systems. The carbon block filters are manufactured with high purity Coconut Shell activated carbon with extruded activated carbon block construction. They do not release carbon fines and they are FDA compliant and they are NSF certified. These solid carbon block filters have combined the adsorption capability of carbon, with the ability of a solid block material to selectively strain out particles from the water that is being forced through the filter. Activated carbon has an electro-positive charge added which results in this type of carbon attracting more chemicals and impurities. As the water passes through the positively charged carbon, the contaminants with their negative ions, are attracted to the carbon granules and thus extracted from the water. The block of carbon strains out sediment, dirt, bacteria, microscopic worms, algae, asbestos and cryptosporidium. With just water pressure, this compacted solid carbon block is designed to filter sub micron size particles. This microstraining of the water will provide the cleanest and clearest drinking water available. Activated carbon bonds to thousands of known chemicals. As water is forced through this solid block of carbon, it is forced to slow its flow speed and thereby increase the contact time with the carbon. This slowing of the flow allows the carbon bonding to take place and remove chemical pollutants like toxins, THM's, chlorine, pesticides, bad tastes, odors, etc. Solid block carbon filters are very uniform and do not channel or bypass as conventional granular activated carbon (GAC) filters are know to do. Because of the density of the solid block carbon filters, there is no room for bacteria to grow, so these filters do not become an incubator for bacteria as GAC filter are known to be. These carbon block filters will fit most types of 10 filter housings on the market today and as noted previously, they will fit into the housings on nearly all water filtration and reverse osmosis systems. Carbon block filters preform well in both commercial and residential applications and they are the most widely used carbon filters on the market today. The inline filter is manufactured with a high performance granulated activated carbon that polishes the product water as it moves from the storage tank (on your reverse osmosis system) to your usage point. As it moves through the filter, the inline filter eliminates any tastes and odors that may arise before the usage point. The inline filter is 10" in length and has a 2" OD with quick connect fittings. It is recommended that you install a pressure regulator if your incoming water pressure exceeds 70psi. All of the sediment and carbon filter housings are standard 10 inch white housings with 1/4 inch thread inlets and outlets. 10 DI Refillable Filter In-Line Housing With DI Resin.

This is a 10 inch refillable in-line Filter Housing with 6 ounces of DI (Deionization - Demineralized) mixed bed resin installed. When this DI filter is installed as the final stage (process) of a 5 or 6 stage Reverse Osmosis system, the 6 ounces of resin will reduce the TDS of the already processed RO water.

The DI resin MAY reduce the TDS down to or near zero TDS. But since this depends on the feed water quality, the pressure fed to the RO membrane, the temperature of the water, the quantity of water the customer uses... And various other conditions we can not guarantee zero TDS water nor how long the DI resin will last. This stage requires maintenance (replacement) and might need to be done often if you require zero TDS consistently.

Reverse Osmosis units are capable of removing 90% to 95% of the TDS (Total Dissolved Solids). If your water usage requires zero (0) TDS, this 10 refillable in-line will provide the quality of water you are seeking. This DI in-line Filter Housing is compatible with RO systems and will polish the water to the highest quality of zero (0) TDS. The housing is 2" x 10" with input and output 1/4 inch FPT.

The cap can be easily removed to dispose of the old resin and then refill with new resin when your filter requires attention. As noted above, this is a complete system. We install these units daily.

Where you will find over a dozen different sizes and types of whole house units - single housing, dual housing and triple housing units - slim line, standard and Big Blue housing types - clear, blue or white - a size and type to fit everyones needs. To see Reverse Osmosis systems of various capacity and types - we do not offer one RO system that fits all, rather we offer a variety to permit you to select a system that meets your specific needs. Should you need to upgrade your current RO system, we have packages to make the upgrade easy for you to complete. We are offering you products that we believe in and use everyday in our water serving operation which covers several states. Compare our prices - we can offer quality products at better prices because of volume usage. For the last 20 years we have been servicing water equipment in several states. During this time we have used thousands of sediment and carbon block filters - we are offering you products we have used over the years and found to provide us the quality of service life our customer have come to expect.

When we started in the water business in 1984, many of our competitors were still drinking chlorinated water. We are a member of the Water Quality Association (WQA is an international organization) and we adhere to the code of ethics of this the premier water organization in the world. The item "6 Stage RO+DI NT white Reverse Osmosis System 24/35/50GPD Drinking Water Filter" is in sale since Monday, November 7, 2011.

This item is in the category "Home & Garden\Kitchen, Dining & Bar\Small Kitchen Appliances\Water Purification\Water Filters". The seller is "h2osplash" and is located in Great Bend, Kansas.

This item can be shipped worldwide.

Brand: H2O Splash
MPN: Does Not Apply