This Product has been customized/built in the USA. This RO four (4) stage system with 75 gallon per day membrane will provide top quality water. Clear housings, on the two pre-filters, not only make this unit sparkle, this feature also takes the guess work out of replacement of filters. 4 Stage Reverse Osmosis System.
This sale is for one (1) four stage reverse osmosis system. The system includes a 75 gallon per day CSM membrane, membrane housing, flow restrictor, one sediment filter and clear housing, one carbon block filter and clear housing, one booster pump, one in-line carbon filter, saddle valve kit, automatic shut-off valve, fittings, check valve, tubing and filter wrench.This is an assembled RO system (ready to be installed). Reverse Osmosis Pressure Gauge Kit - Many folks with RO systems are searching for a method to determine when to change their filters. We offer a Pressure Gauge Kit that will take the guess-work out of when to replace your filters. Special Note 2 : All of the housings (sediment and carbon filter) are standard 10 inch clear housings with 1/4 inch thread inlets and outlets. Clear housings will permit you to observe the filters and thereby allow you to monitor the depletion of the filters. This will take the guess work out of when to replace your filters. Special Note 3 : This RO system comes.
And without a faucet kit. The system is customized for users with an existing storage tank or for dispensing directly into an aquarium. Reverse osmosis membrane elements for home drinking water are the among industrys most reliable. Advanced membrane technology and automated fabrication allow these elements to deliver consistent performance that equipment suppliers, water treatment dealers, and residential customers can rely on.
These elements are NSF Standard 58 listed. Dry type elements are vacuum leak tested using the Sandiego Protocol so that the performance shall satisfy their specifications. Model Flow Rejection Diameter Length Test Conditions Temp. RE1812-24 24 gpd 98% 1.8 inches 12 inches 60 psi / 250ppm 25 C / 77 F. RE1812-35 35 gpd 98% 1.8 inches 12 inches 60 psi / 250ppm 25 C / 77 F.RE1812-50 50 gpd 98% 1.8 inches 12 inches 60 psi / 250ppm 25 C / 77 F. RE1812-75 75 gpd 98% 1.8 inches 12 inches 60 psi / 250ppm 25 C / 77 F. RE2012-100 100 gpd 98% 2.0 inches 12 inches 60 psi / 250ppm 25 C / 77 F.
RE2012-150 150 gpd 93% 2.0 inches 12 inches 50 psi / 100ppm 25 C / 77 F. The stated product performance is based on data taken after 30 minutes of operation at the following.
250 mg/L NaCl solution at 60 psig (0.41 MPa) applied pressure. Dry type elements are vacuum leak tested using the San Diego Protocol. Permeate flow rate for each element may vary but will be no more than 15% below the value shown.
All elements are packaged in a polyethylene bag containing 1.0% SBS (sodium bisulfite) solution. Element configuration: Spiral-Wound, Tape Wrapping. Model A B C D E. 87 inch 11.73 inch 1.77 inch. 47 inch 11.73 inch 1.91 inch.A Diameter of center feed post B. Length from end of feed post to membrane wrap. C Over-all length from end of feed post to end of Permeate post. D Diameter of membrane wrap. E Length from membrane wrap to end of Permeate Post. This 10 inch sediment filter is made of 100% high purity polypropylene, surfactant free, binder free and adhesive free. This sediment has a special design to trap particulates. Sediment filters are in compliance with FDA requirements and they are NSF Standard 42 certified. They have great particle holding capacity and are being used in a variety of applications such as pre-filters for reverse osmosis systems, pre-filters for water filtration units, aquarium pre-filters and being used as sediment collectors for whole house systems. The carbon block filters are manufactured with high purity Coconut Shell activated carbon with extruded activated carbon block construction. They do not release carbon fines and they are FDA compliant and they are NSF certified. These solid carbon block filters have combined the adsorption capability of carbon, with the ability of a solid block material to selectively strain out particles from the water that is being forced through the filter. Activated carbon has an electro-positive charge added which results in this type of carbon attracting more chemicals and impurities.
As the water passes through the positively charged carbon, the contaminants with their negative ions, are attracted to the carbon granules and thus extracted from the water. The block of carbon strains out sediment, dirt, bacteria, microscopic worms, algae, asbestos and cryptosporidium. With just water pressure, this compacted solid carbon block is designed to filter sub micron size particles.
This microstraining of the water will provide the cleanest and clearest drinking water available. Activated carbon bonds to thousands of known chemicals. As water is forced through this solid block of carbon, it is forced to slow its flow speed and thereby increase the contact time with the carbon. This slowing of the flow allows the carbon bonding to take place and remove chemical pollutants like toxins, THM's, chlorine, pesticides, bad tastes, odors, etc.Solid block carbon filters are very uniform and do not channel or bypass as conventional granular activated carbon (GAC) filters are know to do. Because of the density of the solid block carbon filters, there is no room for bacteria to grow, so these filters do not become an incubator for bacteria as GAC filter are known to be.
These carbon block filters will fit most types of 10 filter housings on the market today and as noted previously, they will fit into the housings on nearly all water filtration and reverse osmosis systems. Carbon block filters preform well in both commercial and residential applications and they are the most widely used carbon filters on the market today. Booster Pump, Transformer and Tank Shut-Off Switch.
This is a complete booster pump system (pump, transformer and switch) suitable for use with a Reverse Osmosis System or an application requiring increased PSI. A Reverse Osmosis membrane operates best with 50 or greater PSI and will provide quality water and improved quantity at higher PSI levels. This high feed booster pump system will optimize your RO systems performance. The pump is easy to install and the pressure switch has 1/4 quick connect fittings.
We include installation instructions and a flow diagram to assist you in the set up and installation process. The pump, transformer and switch are installed on this RO system so all that is required is for you to plug into an electrical outlet. This pump will run your RO system at an ideal pressure level regardless of the pressure going in.It is very quiet and totally automatic. It shuts off automatically when the tank is full. This is a "continuous duty pump" designed for years of quiet, efficient service. You will need to listen closely to know it is running and you'll notice a remarkable change in your RO's performance.
You will need 115 volt AC source. The electrical current usage is negligible. This booster pump is designed to accomplish auto suck.
These pumps are 100% tested to insure extended life. The transformer has an input of AC 110 V and output of DC 24 V. The switch turns off the booster pump when the tank is full (on at 30 psi and off at 50 psi). Closed switch can be set at various shut-off pressures. The inline filter is manufactured with a high performance granulated activated carbon that polishes the product water as it moves from the storage tank (on your reverse osmosis system) to your usage point.As it moves through the filter, the inline filter eliminates any tastes and odors that may arise before the usage point. The inline filter is 10" in length and has a 2" OD with 1/4 FPT. It is recommended that you install a pressure regulator if your incoming water pressure exceeds 70psi. All of the sediment and carbon filter housings are standard 10 inch clear housings with 1/4 inch thread inlets and outlets.
As noted above, this is a complete system including installation instructions. We install these units daily. Should you need to upgrade your current RO system, we have packages to make the upgrade easy for you to complete. We are offering you products that we believe in and use everyday in our water serving operation which covers several states. Compare our prices - we can offer quality products at better prices because of volume usage.
For the last 30 years we have been servicing water equipment in several states. During this time we have used thousands of sediment and carbon block filters - we are offering you products we have used over the years and found to provide us the quality of service life our customer have come to expect. When we started in the water business in 1984, many of our competitors were still drinking chlorinated water. We are a member of the Water Quality Association (WQA is an international organization) and we adhere to the code of ethics of this the premier water organization in the world. It is recommended that you install a pressure regulator if your incoming water exceeds 70psi.
These housings should never exceed 70psi. If your water pressure exceeds 70psi it is recommended that you install a pressure regulator.
The item "RO 4 Stage 75 gpd+Booster Pump Reverse Osmosis System Water Filter Clear Housing" is in sale since Sunday, November 13, 2011. This item is in the category "Home & Garden\Kitchen, Dining & Bar\Small Kitchen Appliances\Water Purification\Water Filters". The seller is "h2osplash" and is located in Great Bend, Kansas. This item can be shipped worldwide.